| You are here: Your Model Railway Club > Reference Area. > Hints & Tips > HINTS AND TIPS - THE FOLLOW ON | To bottom of page |
| Recent Topics |
|---|
|
|
||||||
| ||||||
| Moderated by: Spurno | Page:   ... 97 98 99 100 101 102 |
|
||||||||
| HINTS AND TIPS - THE FOLLOW ON - Hints & Tips - Reference Area. - Your Model Railway Club | ||||||||||
| Author | Post | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2534 Using Isopropyl Alcohol when Ballasting Pt 2, By Wayne Toth, I do not care for alcohol as a wetting agent for ballast (or ground cover, either) as I usually work on longish sections of track or large scenic areas, and most of it would be evaporated before I got finished. I also don't care for the smell of it, but have no arguments against the drinking kind of alcohol. If your tap water is fairly hard, an alcohol mixture might work better, but you could also use distilled water. I sometimes use water from the trainroom's dehumidifier - as long as the water-collecting bucket is cleaned beforehand. It is a decent equivalent for distilled water. FROM TREVOR Just a heads up that we are within 13 H&T's or so away from the end of the current queue. Anybody in the group can simply PM me if they have something they would like to share but if I have run my race, well, 13 years between mremag and YMR forum is not a bad innings. The first 499 will continue for a while longer of course. If I do come across anything of use I will update it but it has been a few months since I have seen anything that has not been covered by us in one form or another! Hope you can understand that I am not an eternal fountain of info but hope you have enjoyed what you have read so far. I will be continuing in the hobby and inputting with Rail Modeller Australia of course. Cheers Trevor |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2535 A different approach to Ballasting, By Dave Nelson, When ballasting, I use a chunk of cork roadbed which happens to be about HO width. I use it as a sort of bulldozer to push the ballast down to the level of the tops of the ties, and scrape away ballast from the inner edge of the rail where the spike heads (or for Atlas track, the shoe boxes) are. I then do the same for the outer sides of the rail. Then I apply the Scenic Cement (or diluted matte medium, or a distilled water/white glue/isopropyl alcohol/india ink mix) in a pipette or drop applicator. I do NOT touch the ballast then even if I see something wrong until it hardens. Then I go over it again with that cork bulldozer and generally try to recapture and reuse any ballast that is bulldozed up (it may need to go through a sieve). Sometimes ballast needs to be reapplied here and there; sometimes the liquid cement application causes a bit of a crater or bulge that needs to be addressed. After yet one more run with the cork bulldozer, and again trying to capture and save any ballast that is brushed up, only then do I vacuum. Sometimes I need to do a bit more to get rid of the stray grains of ballast that stick to the sides of rails or the tops of ties. If there is quite a bit of that, one more vacuuming might be needed. Ideally when I ballast I like to have enough materials, and enough time, to do several feet of track at a time. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2536 Painting a Chain Link Fence By Andrew Jamieson I was tempted to paint it a model chain link fence with an aluminium colour then weather accordingly. However a close examination of a relatively new fence found it to be “greying” very quickly with the zinc oxide. So a change to either a Humbrol No 64 or a Revell Mouse Grey proved closer to the mark for me in my lighting situation. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2537 Replacing Brick Paper and Attaching it to Plastic. By Phillip Quinn I print the brick detail on to self adhesive labels. It is a lot less messy than spray adhesive and it also stops the plastic being “warped” by spray adhesive or PVA glues when the glue begins to dry and subsequently shrink on one side, causing the buckling! |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2538 Roofing vs Locale By Nathan Harrison When building your industrial sites, in relation to the roofing, I suggest you consider the area you are modeling because climate may affect the color of the roof you are modeling. In areas where high temperatures are common, light grey, and white are popular. Although other darker colors are found, mostly light browns and tans, very light greys are industrial and residential winners, due to their ability to reflect the sun and lighten the load on air conditioning. For textured roofing, I use 200 grit sand paper and paint it the colour I require, As the roof ages, streaks begin to appear as windborne dust accumulation and loss of stone washed away by heavy rain occurs, revealing weathered tar in streaks, heading for low points and, the nearest down spouts. Fortunately, in the age of the internet, I can use Google Earth to "visit" various rooftops for inspiration in my Texas modeling. Don't forget the dirt accumulation in the low spots and the fresh(er) tar from repairs. In the hostile conditions down here, it doesn't take long for the elements to knock the shine off a new roof so, I would never use gloss, or black on a roof. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2539 Dusting Rolling Stock and Structures By Wayne Toth Using a brush to remove dust from structures and rolling stock only works well if you take those items outdoors to do the cleaning - if done in the layout room, the next time you walk into that room, the disturbed dust will migrate right back to where it had been before. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2540 Dusting Layouts By Robert Bell I am not a big fan of sprays for cleaning my railway. I bought some for fake house plants but found out window cleaners with ammonia cheaper and better. Most scenery has to be redone to some extent. First off is to keep scenery as clean as possible from the get go and plan for cleaning and lighting is very important as you do not want fluorescents or incandescents. Rocks can be restained as long as they were not sealed. You can vacuum the ground cover and hairspray on a touchup layer on bushes. All my trees are removable along with most buildings. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2541 A different Technique for getting an “Aged Concrete” Look in the absence of Polly S paints Pt 1 By Dave Nelson Since Polly S “Aged Concrete” paint is not longer available, I have used Tamiya rattle can paints where I spray two colours at the same time, creating a varied and blended look that I think is convincing. The two colours that work best for concrete for me are TS-68 Wooden Deck Tan or AS-15Tan (USAF) PLUS AS-16 Light Gray (USAF). It takes some practice. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2542 A different Technique for getting an “Aged Concrete” Look in the absence of Polly S paints Pt 2 By Mark Redding I've built a lot of concrete structures - from coal towers to bridge abutments - and needed a lot of base concrete color. My solution was to take my favorite base color (Floquil Aged Concrete) to the local paint store and had them mix me a quart of flat latex paint to match it. Flat latex paint works surprisingly well on everything from styrene to plaster. I've even had success in thinning it and airbrushing it. The quart of paint cost about a much as two bottles of Floquil ! |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2543 Glues for 3D Printing By Peter Wheeler Depending on what type of material your 3D printed parts are made from many glues are suited to 3D casting and moulded. CA (Superglue) will work on pretty much all 3D printed parts. Just make sure you clean parts first. A lot of commercially printed parts have a residue on them that paint and glue do not like to stick to. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2544 Cleaning “reluctant” Spray Can nozzles By Joseph Medina What I found that works in salvaging rattle can nozzles, especially Rustoleum with the fat nozzles, is CRC Electronic cleaner although any electronic cleaner should do. Just remove the nozzle after using, and give the outside/inside a quick spray. It removes the paint and dries very quickly. It comes with a small spray hose which can be aimed up the nozzle. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2545 Capping Stone Walls By Paul Grant I have capped stone and brick walls simply by cutting one line off a styrene sheet of a stone or brick pattern and gluing it to the top of the "wall". A bit of sandpaper and paint finish it off. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2546 Painting Stock Pens By Several Modellers Unless you're modeling a recently-built stock pen, if the fences are wood they should be a weathered light grey. Add some soil color (whatever your local color is) along the lower sections, and some brown here and there to represent that stuff found on the ground all in stock pens. - Scott Chatfield It depends on the location you're modeling. As mentioned by others, pens can vary depending on local custom and regional types of wood. Here in Colorado, stock pens are a rather brown with subtle gray tones depending on the whether a particular side faces the sun or not. There's probably a lot of photos on-line. Just put on your cowboy hat and search "stock pens". (Paul Kessler) |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2547 Protecting Backdrops when applying scenery By Several Modellers To protect my backdrop from 3D plastering added to the front, I I used thin plastic styrene sheeting between the backdrop and the work I was doing and removed it before the scenery work dried, worked very well. (Richard Bell) I cover my photo backdrops with wax paper to protect it from the 3D scenery. (Mark Pruitt) |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2548 Metal Sand Pipes Pt 1 By Mike Griffin I use brass wire of about .6mm for my sanding tubes so I avoid accidentally stabbing my fingers when picking up my locos, rather than hard metals such as stainless steel. It's better to damage the sand pipe than stab your finger. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2549 Metal Sand Pipes Pt 2 By Martin Kernow I've done lots of sandpipes on various locos, both detailed RTR and etched chassis kits and I almost always use a soft fuse wire, 10 amp, I think - the sort you get with two other types of fuse wire, wound round a little card from hardware stores. I abrade it gently with some wet and dry, holding one end in a pair of pliers or vice and then cut and shape to fit. Having abraded it, perhaps so that the silvery coating is removed or partially removed, revealing the soft copper underneath, I find that it takes paint well. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2550 Hidden Staging Yards Pt 1 By Dave Husman My hidden staging yard was under the layout main level but there was a gap in the fascia that would let you see the switches or if it was hidden behind scenery the switches and staging tracks to the clearance point were visible. The train was hidden, not the switch. As far as fitting, the train would hold X number of cars and the normal set of power. The track would handle X + 3 cars. As long as you obeyed the train size constraints the train would fit. On the stub end tracks there was a styrofoam bumper on the end of the track. You could run into it but not off the end of the track. On stub end tracks that were semi-visible I would put 1/2 a boxcar with the knuckle removed from the coupler on the end of the track. If you did lean over and look down the track, you would see a boxcar. The train or cars shoved into it would bump couplers but could not actually couple up. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2551 Hidden Staging Yards Pt 2 By Several Modellers I used a mirror on a previous layout and it worked fine for checking that the trains were not fouling the turnouts. (Nevin Wilson) I have a video camera although it's an older analog one which hooks to an old analog TV. The picture isn't great. I might upgrade to digital although I haven't priced them recently. I use car cards and have a card for each loco which is the top card for any train. When a train goes into staging, I have pockets on the fascia for each staging track and I put the train's car cards in those pockets which tell me which loco is on each track. (John Newridge) |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2552 Keeping track of Hidden Staging By Neal Paladini I have a lot of staging tracks that are not as visible if there are other trains/engines in front of it. What I do is to keep a small index card and pen/pencil and I write the engine number and track number on the card to keep track. With 6 tracks not that visible, it is important that I write them down, especially as I get older, the memory is not what it used to be. |
|||||||||
| ||||||||||
| ||||||||||
|
xdford Member
My photos:
|
Hints & Tips No. 2553 Making Realistic Bark on Taller Trees By Several Modellers Take a tapered dowel and add spackle to the trunk area, then while still wet add bark detail, I use a hobby saw for this. When dry paint with black spray paint and then dry brush your tree colors to suit, don't forget your highlites to make the bark pop. (Richard Bell) he first thing about trees is that you need the right bark texture, and that really comes out in the picture. So let's assume you have achieved that. If you don't, you can create that using the blade of a saw, rubbing the trunk laterally with the saw blade to create crevices. (Simon Roy) |
|||||||||
| ||||||||||
| This is topic ID = 5310 Current time is 01:17 pm | Page: ... 97 98 99 100 101 102 |
| You are here: Your Model Railway Club > Reference Area. > Hints & Tips > HINTS AND TIPS - THE FOLLOW ON | |||
|
You can type a quick reply to this topic here. Click in the box below to begin. Or to reply to an individual post, or to include images, attachments and formatted text, click the Quote or Reply buttons on each post above. To start a new topic in this forum, click the Start New Topic button below. To start a new topic in a different forum, click the Forum Jump drop-down list below. |
|
||
|
Back to top of page | ||
| |||
| Problems with this web site? Please contact the Webmaster. | |||
| All material submitted to this web site is the responsibility of the respective contributor. By submitting material to this web site you acknowledge that you accept full responsibility for the material submitted. |
| Unless stated otherwise, all the material displayed on this web site, including all text, photographs, drawings and other images, is copyright and the property of the respective contributor. Registered members are welcome to use it for their own personal non-commercial modelmaking purposes. It must not be reproduced or re-published elsewhere in any form, or used commercially, without first obtaining the owner's express permission. |
| The owner of this web site may edit, modify or remove any content at any time without giving notice or reason. © 2008 |
| Recent Topics | Back to top of page | |
|
Powered by Copyright © 2007-2011 by Jim Hale and Data 1 Systems. Page design copyright © 2008-2013 Martin Wynne. Photo gallery copyright © 2009 David Williams. |
||