Video Archive | Recent Topics |
---|
![]() |
||||||
| ||||||
Moderated by: Spurno | Page: 1 2 3 4 ![]() ![]() |
|
Scalescene Warehouse.....somewhat modified for Granby - Scalescenes Building Kits. - More Practical Help - Your Model Railway Club | ||||||||||
Author | Post | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||
John Dew Full Member ![]()
My photos:
![]() |
The latest project on my Granby layout is a city centre goods yard. As you can see it will occupy a corner of the layout. It will need lots of low relief backscene that relate to the goods yard ![]() The first building will serve as a functional backscene for the siding on the left. The plan is to build 3 modules of the Scalescenes Warehouse (http://www.scalescenes.com/products/T026-Factory-warehouse......usual disclaimer). Some members may have already built this kit and I know most have built one or other of John Wiffen's other kits so I apologise for any needless repetitition There is, however, no doubt that this is a quintessential Scalescene Design.... multi layers.......revealed openings ......glue and wrap trim......and so on......so here goes: Print out the Top Base Layers and glue them on to Medium Card (1mm) ![]() The kit is amazingly flexible.The basic upper level module shown above measures 250mm x 165mm, but you can see from the hash marks (which are really handy) it can be sub divided into 4 columns each 62.5 mm wide and three floors each 55 mm high so there are lots of opportunities for relatively trouble free customisation ![]() Cut out the openings.....I am going to build a grain hoist so I didnt bother cutting out the second column ![]() Print out the upper level top overlay and cut out the openings. Apply an even coating of adhesive (I use UHU sticks) to the base layer and carefully position the overlay over the base using the guide marks. There are lots of helpful arrows pointing [TOP] its a good idea to obey them (dont ask how I found out!) because the window opening has a brick architrave at the top ![]() You then have to glue and wrap the printed side pieces so that the cut edges are concealed (partly done above). If Doug is reading this (and I hope he is).....please dont look too carefully......the edges do not have anywhere the crispness that you achieve.......my feeble excuse.....its a long way away and I had to do 72 of them ![]() The bottom edge is covered with a brick sill trim. The camera angle shows the top cut edge......not sure how it will look in situ but I think I will paint it out with water colour before attaching the top layer The next shot shows the base layer roughly positioned under the top layer ![]() Eventually these apertures will be cut out and another overlay applied with further apertures cut to accommodate windows. This shot shows the lower level layers. I am afraid I cut them out and applied the overlay before I remembered I needed to take photos........but the principles are identical to those described for the upper level ![]() As you can see the top layer is just a series of rectangular openings to which I have glued and wrapped the overlay. The base layer has a variety of options. In this shot of I am only using 2 of the 5 available.... Loading Bay (which has appropriate trim) and a blank wall. Other options include Window, and two types of full length Door.......all the Door Openings have different door options Here are the three lower level modules for my design ![]() There are four loading bays and one doorway that will give rail access to the the warehouse via a wagon turntable Departing from the kit there will be a scratch built loading platform ....... which is why some of the brick walls are not completely covered (waste not, want not).....I also have to infill the space between the two layers.......the bits of white card at the bottom The extreme left and right modules will be exposed so the infills there are clad in brick Finally a rough assembly of the three modules (upper and lower) with the infills in place,the bearer for the platform glued on and one uncut upper level base layer overlay for effect. ![]() Above each of the two central doors there will be a scratch built Grain Hoists.....the pencil crosses are to remind me not to cut! The modules will eventually be joined together vertically by substantial (2mm) buttresses and horizontally by 2mm ledges Without the roof ......which I am stll contemplating.....the warehouse will be 250 mm high......a metre long and about 30mm deep.......I did say ultra low relief ____________________ John Granby III Lenz DCC,RR&Co Gold V9 B1 Windows 10 |
|||||||||
|
| ||||||||||
Chubber Casseroled Badger ![]()
My photos:
![]() |
72! I bet your poor paws will be sore at the end of that session! Bon corage, mon brave... Doug ____________________ 'You may share the labours of the great, but you will not share the spoil...' Aesop's Fables "Beer is proof that God loves us and wants us to be happy" - Benjamin Franklin In the land of the slap-dash and implausible, mediocrity is king |
|||||||||
|
| ||||||||||
Petermac Moderator ![]()
My photos:
![]() |
I remember building it for the Maxmill module John. Perhaps not the complexity of the large station but lots of cutting, folding and glueing. It makes up into a really superb model and, like all his kits, as tough as boots. Yours looks like a very substantial warehouse and will form an excellent backdrop to the yard. I remember seeing lots of these structures around the industrial north - and "powerful" building they were too. ![]() ____________________ 'Petermac |
|||||||||
|
| ||||||||||
John Dew Full Member ![]()
My photos:
![]() |
My apologies for the disjointed nature of this post......for some reason I cant edit the first line.....n attempts.....I give up....so let me repeat....thanks Doug and Pete! You are absolutely correct about the robustness of the kits. I think one of the best things about building them is the steady increase in mass and structure.....I am astonished at the weight so far and it is only half finished I am using photos from Iain Rice's book and Bob Esserry's as a source of ideas......just hope it all comes together with the sense of time and place that I am aiming for The amount of cutting on this project is amazing!!! My sincere thanks to all the guys who set me on the right path when I was bulding the station roof by suggesting I use a snap off craft knife rather than a scalpel.....I can almost afford another pannier based on the savings.......and thats not accounting for the time saved! So now on to the upper level base layer ![]() I use spray adhesive to fix the sheets to the card and a sort of sponge squegee to eliminate any bubbles (well most of them) Next step cut out the apertures (x3) ![]() I am probably stating the obvious, but there may be others as impractical as I who may benefit. I have learned not to cut each aperture individually......rather I place a steel rule along the base of the first row of windows and then, with a new blade, make a firm but not too deep pass at the base of each window and then on to the next row.......then I do the verticals. Finally with a new Exacto blade I cut the curved arch. Once these initial cuts outline have been made, I make a series of light cuts with the dulled blades. Next step is to cut the apertures in the overlay......sharp scalpel blade again. Then glue to the base layer. I found the easiest way was to use a glue stick over the entire base but only to present the very top of the overlay using the guide lines on both overlay and base to ensure a perfect match........and only then allow the balance of the overlay to make contact with the adhesive. Trying to fiddle with the overlay once on top of the base was fraught with difficulty! ![]() This shot shows the different stages required to achieve the completed window frame. 1 Left hand column...... Overlay on top of aperture 2................................ Tab wrapped and glued around aperture 3................................ Window Sill cut out and glued in place.......lining these up was rather more difficult than the text implies 4................................ Wrap and glue Generally I have found it best to glue the sill, or whatever, in place and let it dry before attempting the wrap and glue the balance. The camera angle shows the uncovered upper cut edge on each window. This close up shows it even more ![]() I have always painted out the cut edges on Metcalfe Kits......and did the the same here .....just using roughly mixed water colours. ![]() If it were closer I would probably paint the cut edge of the sills but in this instance didnt bother So a few days later......and many blades later I was able to join the upper base layers with the upper top layers ![]() Before joining the upper and lower levels I decided to make the platform serving the loading bays ![]() I built this using bits and bobs from the Scalescenes Plat form kit. The support wall is clad with blue engineers brick.....a ramp at one end and steps at the other. There is not a lot of space between the back wall and the siding but I felt 6 scale ft would be realistic The steps were built up with bits of card in the same manner as the subway steps on Granby ![]() The brick piers on the support wall are probably not prototypical but they conceal a couple of not very good joins Cutting out and covering the platform was quite tricky because I had to allow for all the doorways ![]() The blackish paint next to the coping stones is a good example of learn as you go. When I laid up the paving stones against the coping stones there was a slight, almost imperceptible (but still obvious to the naked eye), gap.....and the white of the base layer glared through.........the heavy line results from a retro correction..........if however you paint the base before the pavers are applied you can get away with it! ![]() in the shot above I have put some dark board behind doorway #4 ![]() As you can see there is very little available space at the back........it is ultra light relief!! Clearly some of the doors have to be open......I want to create a sense of activity....movement...pallet loads of apples and bananas being offloaded....... I am struggling a little to work out how to achieve this...................meantime I have to cut out and clad 22 buttresses and 72 +- ledges and then I can join the upper and lower levels together......first step .....buy some more blades. ____________________ John Granby III Lenz DCC,RR&Co Gold V9 B1 Windows 10 |
|||||||||
|
| ||||||||||
MaxSouthOz Admin ![]()
My photos:
![]() |
It's really odd, John. Could it be that you are using data from another forum? Maybe Martin might be able to spot it. ____________________ Max Port Elderley |
|||||||||
|
| ||||||||||
Petermac Moderator ![]()
My photos:
![]() |
It's looking excellent John - and massive !!! Your arched windows are infinitely better than mine were - maybe Canadian knives are sharper than French ones - we don't have to fend off Grizzly's .......... ![]() ![]() Your tip about either painting the platform sub-base or marking it with that black line is one that is firmly filed away for future reference. ![]() As I said in an earlier post, this is going to be a very impressive warehouse. ____________________ 'Petermac |
|||||||||
|
| ||||||||||
Angusog Full Member
My photos:
![]() |
I may be way off here, but i had a similar problem replying to my own topic Max, i was trying to insert a quote and started it on the first line it was difficult to delete, i exited the post and started again without sending, then hit enter to move the quote down a line and then i could get out of the quote box... hope this helps Robert ____________________ ____________________________________________________ Robert céad míle fáilte |
|||||||||
|
| ||||||||||
ddolfelin Straight man to the stars. ![]()
My photos:
![]() |
A definitive build for the index I would think. Well done, John. ____________________ http://dddioramas.webs.com/ 11 + 2 = 12 + 1 |
|||||||||
|
| ||||||||||
John Dew Full Member ![]()
My photos:
![]() |
MaxSouthOz wrote: It's really odd, John. Ron has Pm'd me........my apologies for any trouble I have caused. Like others, I am obliged to be a member of two forums and post identical or near identical posts.....not being very technical I hadnt realised I was the cause of the problem ![]() Again my apologies ____________________ John Granby III Lenz DCC,RR&Co Gold V9 B1 Windows 10 |
|||||||||
|
| ||||||||||
John Dew Full Member ![]()
My photos:
![]() |
Thanks for the kind words DD and Peter Petermac wrote: It's looking excellent John - and massive !!! ![]() ![]() Actually we dont get Grizzlies here but there are lots of Black Bears.........which are big enough. I wouldnt be fending them off with a scalpel...............the trick is to make lots of noise wherever you walk in the parks.....when they appear in gardens (which they do regularly)......get inside the house ![]() ____________________ John Granby III Lenz DCC,RR&Co Gold V9 B1 Windows 10 |
|||||||||
|
| ||||||||||
Petermac Moderator ![]()
My photos:
![]() |
I usually do make lots of noise in the woods and parkland - that's probably why I've never come across a bear over here............![]() ![]() Would wild boar do as a substitute ? ____________________ 'Petermac |
|||||||||
|
| ||||||||||
John Dew Full Member ![]()
My photos:
![]() |
The last two days have been Wet Wet Wet here (today I found the sun still exists) so I was able to press on with construction. The completed upper and lower levels are joined vertically by buttresses....earlier I incorrectly stated they were 2mm thick ......actually they should be and are 4 mm thick.......two pieces of 2mm x 10mm x 250mm laminated together and clad with brick paper......13 buttresses therefore 26 pieces of card. ![]() ... They are joined horizontally by 10mm x 50mm ledges clad in very skilfully weathered concrete......I needed 30 of these but misread the instructions and made them 2 ply so I cut 60 to be at the same level ie flush with the buttresses......labour apart I think it is actually better this way but it was more accident than design! The instructions tell you to place the buttresses in place and then fit the ledges.......I was concerned about gaps and mis fits.....so I started at one end with one buttress and ensured it was perfectly vertical and that the wall elements were firmly secured....having glued the buttresss I then added the first three ledges ensuring they were at right angles (although not quite as you can see....Doreen came home...the dog barked etc etc) and then glued the second buttress.......and so on. That way I could hide any gaps under the grain hoist columns........as it happens they were all a relatively snug fit......but I still think this is a better way of proceeding ![]() This shot shows the weathering I described. There is a slight downside in that the ledges are designed for one module. If you make three as I have done the effect can look slightly unrealistic.........I decided that the prevailing wind at Granby was easterly and turned some of them upside down and moved them around so that the more heavily weathered ledges were in the most exposed places......when I add some pastel weathering I will try and add to this. I got so caught up with cutting and glueing and wrapping that I omitted to take any photos.......but this shot shows the final stages inserting the 12 top ledges ![]() These are also supposed to be one ply but again I made them 2 ply to be flush with the buttresses.......cutting these out was more than a little fraught they are only 2.5mm deep........fortunately all my fingers are still present and correct Next step was to fit the roof coping stones......after all the fiddly stuff this was almost a no brainer ![]() If the building was three dimensional there are a number of roof options......and I did contemplate adding a low relief tiled roof but I think it looks fine as it is. Next the windows......printed out on transparencies ![]() I only need the small ones......the larger ones are for windows on the lower level (if used) and the rectangular ones are North Lights for the roof. With the wide black border they were surprisingly easy to align and fit......much simpler than the Metcalfe equivalent......I fit them using a glue stick on the reverse side but based on bitter experience adopted a belt and braces approach with masking tape! ![]() ![]() Next step......the doors but I thought I would close by reminding you how ultra low profile it is! ![]() ![]() ____________________ John Granby III Lenz DCC,RR&Co Gold V9 B1 Windows 10 |
|||||||||
|
| ||||||||||
Sol A modelling Moderator. ![]()
My photos:
![]() |
What are you having behind the windows John? Will you be able to see through them?
____________________ Ron NCE DCC ; 00 scale UK outline. |
|||||||||
|
| ||||||||||
Petermac Moderator ![]()
My photos:
![]() |
Now that's what I call a warehouse ![]() ![]() ![]() Excellent stuff John and I think you might be right about the ledges etc. being the same depth as the buttresses - they do look good (although I also think they look good recessed) ![]() As Sol said, are you going to have some kind of print behind the windows ? I know they're not exactly tranparent, but you can see through them in places .............. ![]() Maybe just a "flat" of some stores or handling machinery etc....... I don't think they had pallets in those days. ____________________ 'Petermac |
|||||||||
|
| ||||||||||
John Dew Full Member ![]()
My photos:
![]() |
Thanks Ron and Peter.....glad you like it.As Sol said, are you going to have some kind of print behind the windows ? I know they're not exactly tranparent, but you can see through them in places .............. The warehouse will be hard against the wall.......if I can squeeze a few mm I will set back some dark card to create a three dimensional effect.......this is particularly important for the open doorways ......some of them will have to be open to suggest some activity.......I have a slight problem in that the platform and particularly the over hang are a little wider than I intended so I have lost some of the space I thought I had left......I may have to wait until the base board is actually in place on the layout
I have been setting my mind to that! I do want it to look busy! Previously I have never used the Ratio Pallets that come with their barrel and drum kit.......but when I googled I found that the first fork lift was built in 1925 and during WWII the use of pallets became much more widespread......so maybe a couple of flats of Apple Boxes might work along with sacks for the Grain and Potato Warehouse above. Still a lot to do.......Doors, Grain Hoists, Canopy, Signage and some people.....oh and some weathering ____________________ John Granby III Lenz DCC,RR&Co Gold V9 B1 Windows 10 |
|||||||||
|
| ||||||||||
Geoff R Member
My photos:
![]() |
It is looking very good, John. I admire your ability to stick with it and make all of those many cut-outs! It will provide an excellent backdrop to that corner of the layout. | |||||||||
|
| ||||||||||
ddolfelin Straight man to the stars. ![]()
My photos:
![]() |
"I think it looks fine as it is" Me too. ____________________ http://dddioramas.webs.com/ 11 + 2 = 12 + 1 |
|||||||||
|
| ||||||||||
Wayne Williams Member ![]()
My photos:
![]() |
I see that you are not having issues with the model staying flat. If I tried that with styrene, I would have to be very careful to prevent it from warping. It sure looks good John. Wayne ____________________ My Layout "The South Shore Line": http://yourmodelrailway.net/view_topic.php?id=509&forum_id=21 |
|||||||||
|
| ||||||||||
John Dew Full Member ![]()
My photos:
![]() |
Thanks guys I still have to ballast and infill Geoff before I can put the module in place but I am beginning to get a sense of how it will look when in situ. Wayne.....I think this is why laminating is such an integral part of John Wiffen's design process.......If you stick a cover layer on a long not very wide piece of single ply there is a tendency to warp but once you laminate another component in place it disappears......the structure is extremely robust ____________________ John Granby III Lenz DCC,RR&Co Gold V9 B1 Windows 10 |
|||||||||
|
| ||||||||||
Bod Member ![]()
My photos:
![]() |
Very nice build going on here, John. I remember seeing a photograph placed behind a door and the perspective was good enough to fool you into thinking that the warehouse went back a long way. I'm not sure if it was on here or elsewhere, I will try to find it. Edit: I can't immediately find it, but I'll keep looking. |
|||||||||
|
This is topic ID = 9727 Current time is 06:13 am | Page: 1 2 3 4 ![]() ![]() |
You are here: Your Model Railway Club > More Practical Help > Scalescenes Building Kits. > Scalescene Warehouse.....somewhat modified for Granby | |||
You can type a quick reply to this topic here. Click in the box below to begin. Or to reply to an individual post, or to include images, attachments and formatted text, click the Quote or Reply buttons on each post above. To start a new topic in this forum, click the Start New Topic button below. To start a new topic in a different forum, click the Forum Jump drop-down list below. |
|
||
|
Back to top of page | ||
| |||
Problems with this web site? Please contact the Webmaster. |
All material submitted to this web site is the responsibility of the respective contributor. By submitting material to this web site you acknowledge that you accept full responsibility for the material submitted. |
Unless stated otherwise, all the material displayed on this web site, including all text, photographs, drawings and other images, is copyright and the property of the respective contributor. Registered members are welcome to use it for their own personal non-commercial modelmaking purposes. It must not be reproduced or re-published elsewhere in any form, or used commercially, without first obtaining the owner's express permission. |
The owner of this web site may edit, modify or remove any content at any time without giving notice or reason. © 2008 |
Recent Topics | Back to top of page | |
Powered by Copyright © 2007-2011 by Jim Hale and Data 1 Systems. Page design copyright © 2008-2013 Martin Wynne. Photo gallery copyright © 2009 David Williams. |