| You are here: Your Model Railway Club > Getting You Started. > The Lineside. > Peco 00 Turntable Kit - Project By Perry | To bottom of page |
| Video Archive | Recent Topics |
|---|
|
|
||||||
| ||||||
| Moderated by: Spurno | Page:   1 2 |
|
||||||||
| Peco 00 Turntable Kit - Project By Perry - The Lineside. - Getting You Started. - Your Model Railway Club | ||||||||||
| Author | Post | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||
|
Robert Deceased Member 
My photos:
|
Looking at the last photo, it has just occurred to me that I may have another use for some of my cork tile scraps; I reckon if I glue some of them on the underneath of the turntable well it might deaden the noise considerably. Maybe later...... :-) Perry ____________________ The time in Spain is : Barchester |
|||||||||
| ||||||||||
| ||||||||||
|
Flashbang Former Member
My photos:
|
Hi Has anyone yet devised an Indexing method that works and is not overly complex?? The Peco TT is a lovely kit and works well with suitable motor drive. So come on someone must have devised an indexing system surely? :-) |
|||||||||
| ||||||||||
| ||||||||||
|
projektmaker2008 Full Member 
My photos:
|
These Peco turntables are nice. For a oo gauge kit, can anyone tell me the depth of the well on the outside? In other words what depth is it from under the ledge that the well has? Steve ____________________ Just moved house. A new railway plan is inevitable. Watch this space. |
|||||||||
| ||||||||||
| ||||||||||
|
amdaley Full Member 
My photos:
|
projektmaker2008 wrote: These Peco turntables are nice. For a oo gauge kit, can anyone tell me the depth of the well on the outside? In other words what depth is it from under the ledge that the well has? Hi There.While searching around for topics on motorising the Peco turntable I came upon this old thread.Did you ever get an answer to your question ? ____________________ "The only stupid question is the one you don't ask" Regards. Tony. |
|||||||||
| ||||||||||
| ||||||||||
|
Keith M Full Member
My photos:
|
I've just been to measure my Peco turntable depth. It protrudes 15mm below my board, board itself is 12mm with a 1mm spacer between board and well lip (for levelling purposes) so that equates to 28mm. Since this post was written, there has been a kit developed specifically for this Peco LK55 turntable by a small company called "Locomotech". (http://www.locomotech.co.uk) with whom I have no connection other than as a satisfied customer. The kit itself is very easy to fit to the turntable, and although easier if done as part of initial turntable assembly, can be added later without much difficulty. The motor has an integral gearbox, is very quiet, and can be powered by DC or DCC depending on whatever system you use, either a DPDT centre off toggle switch on DC or, as I have done, with a DCC decoder controlled by my Lenz system. With DCC, you have the option of choosing whichever speed you think suitable, whereas on DC, the inclusion of a suitable resistor in series with the motor is necessary to achieve a suitable speed. Hope this is of some help to you, Cheers, Keith. |
|||||||||
| ||||||||||
| ||||||||||
|
amdaley Full Member
My photos:
|
Keith M wrote: I've just been to measure my Peco turntable depth. It protrudes 15mm below my board, board itself is 12mm with a 1mm spacer between board and well lip (for levelling purposes) so that equates to 28mm. Since this post was written, there has been a kit developed specifically for this Peco LK55 turntable by a small company called "Locomotech". (http://www.locomotech.co.uk) with whom I have no connection other than as a satisfied customer. The kit itself is very easy to fit to the turntable, and although easier if done as part of initial turntable assembly, can be added later without much difficulty. The motor has an integral gearbox, is very quiet, and can be powered by DC or DCC depending on whatever system you use, either a DPDT centre off toggle switch on DC or, as I have done, with a DCC decoder controlled by my Lenz system. With DCC, you have the option of choosing whichever speed you think suitable, whereas on DC, the inclusion of a suitable resistor in series with the motor is necessary to achieve a suitable speed. Hope this is of some help to you, Hi Keith. I've seen the Locomotech motor & it seem to be quality.It seems to be the only decent one out there.There are a couple of indexation motors but they cost an absolute fortune. Regards.Tony. ____________________ "The only stupid question is the one you don't ask" Regards. Tony. |
|||||||||
| ||||||||||
| ||||||||||
|
Keith M Full Member
My photos:
|
When I bought my motorisation kit, Locomotech stated that they were in the process of developing an indexation system compatible with the motor kit and intended to be retro-fitted. I've found that since I can closely overlook the turntable whilst it's operating, and due to the slow speed of the motor, I've not found an indexing system necessary, but I appreciate that this may not be the case for everyone,-"horses for courses" I guess. Keith. |
|||||||||
| ||||||||||
| ||||||||||
|
amdaley Full Member
My photos:
|
Keith. How long have you had your Locomotech turntable unit as I checked their site & they didn't develop the indexation unit. Have you had any problems with it. I'll only need 2 or 3 tracks to my turntable so indexation is unlikely to be needed. Tony ____________________ "The only stupid question is the one you don't ask" Regards. Tony. |
|||||||||
| ||||||||||
| ||||||||||
|
Keith M Full Member
My photos:
|
Hi Tony. It will be about 8 months ago that I bought the kit and fiited it as I built up the turntable. I've not had any problems with it, and to be honest, it's so simple a design that I don't see any reason why I ever should. I have 3 Lenz throttle handsets, 2 pushbutton LH100's which I prefer for loco control and a knob control LH90 which I generally use only to control the turntable motor, so I can vary the rotation speed and direction as I wish. I can only see a need for turntable indexing if you are unable to get close enough to oversee it's operation, not a problem on my layout, and it's added cost and complication I don't need. Keith. |
|||||||||
| ||||||||||
| ||||||||||
|
amdaley Full Member
My photos:
|
Hi Keith. Thanks for that.I have an NCE Power Pro system myself & like you I can look straight down on top of the turntable. So I think I'll go for the Locomotech as I haven't found anything better despite all my searching. Cheers. Tony. ____________________ "The only stupid question is the one you don't ask" Regards. Tony. |
|||||||||
| ||||||||||
| ||||||||||
|
amdaley Full Member
My photos:
|
Got the Locomotech kit. Fitted it with no problem. Just follow the simple instructions. Tested it with an old H & M Clipper. Very smooth & quiet. ____________________ "The only stupid question is the one you don't ask" Regards. Tony. |
|||||||||
| ||||||||||
| ||||||||||
|
Perry Erstwhile scratchbuilder 
My photos:
|
Since my initial motor fit, I too have changed to the Locomotech motor. I run it under DCC, wiring a decoder to the motor as if were fitted in a loco. It runs smoothly and quietly and can turn incredibly slowly. Highly recommended. Perry ____________________ Due to cutbacks, the light at the end of the tunnel has been switched off. |
|||||||||
| ||||||||||
| ||||||||||
|
amdaley Full Member
My photos:
|
Perry wrote: Since my initial motor fit, I too have changed to the Locomotech motor. I run it under DCC, wiring a decoder to the motor as if were fitted in a loco. Happy Holiday Perry.I run my layout on DCC as well but the area where the turntable is hasn't been fully wired yet so i tested it with DC. I plan to fit a decoder to my turntable as well. Very pleased with the Locomotech motor. How do you deal with sound locomotives on the turntable with the polarity change half way round or do you have that problem ? Tony ____________________ "The only stupid question is the one you don't ask" Regards. Tony. |
|||||||||
| ||||||||||
| ||||||||||
|
Perry Erstwhile scratchbuilder
My photos:
|
Hi Tony, I don't have any sound locos at present so this possible problem hasn't come up for me. All I can say is that locos do not need their direction of travel altered when leaving the turntable. The DCC track power is simply routed to the turntable rails and it all just works! I've found no need for reversing gizmos and the like - fortunately! Perry ____________________ Due to cutbacks, the light at the end of the tunnel has been switched off. |
|||||||||
| ||||||||||
| ||||||||||
|
amdaley Full Member
My photos:
|
Thanks Perry.
____________________ "The only stupid question is the one you don't ask" Regards. Tony. |
|||||||||
| ||||||||||
| This is topic ID = 259 Current time is 10:05 am | Page: 1 2 |
| You are here: Your Model Railway Club > Getting You Started. > The Lineside. > Peco 00 Turntable Kit - Project By Perry | |||
|
You can type a quick reply to this topic here. Click in the box below to begin. Or to reply to an individual post, or to include images, attachments and formatted text, click the Quote or Reply buttons on each post above. To start a new topic in this forum, click the Start New Topic button below. To start a new topic in a different forum, click the Forum Jump drop-down list below. |
|
||
|
Back to top of page | ||
| |||
| Problems with this web site? Please contact the Webmaster. | |||
| All material submitted to this web site is the responsibility of the respective contributor. By submitting material to this web site you acknowledge that you accept full responsibility for the material submitted. |
| Unless stated otherwise, all the material displayed on this web site, including all text, photographs, drawings and other images, is copyright and the property of the respective contributor. Registered members are welcome to use it for their own personal non-commercial modelmaking purposes. It must not be reproduced or re-published elsewhere in any form, or used commercially, without first obtaining the owner's express permission. |
| The owner of this web site may edit, modify or remove any content at any time without giving notice or reason. © 2008 |
| Recent Topics | Back to top of page | |
|
Powered by Copyright © 2007-2011 by Jim Hale and Data 1 Systems. Page design copyright © 2008-2013 Martin Wynne. Photo gallery copyright © 2009 David Williams. |
||