Video Archive         Recent Topics      
YMR logo

You are here:  Your Model Railway Club > Getting You Started. > Hints, Tips & Smaller Projects. > Peco Bullhead Track To bottom of page
                 

 Moderated by: Spurno
Start New Topic Reply Printer Friendly

Peco Bullhead Track - Hints, Tips & Smaller Projects. - Getting You Started. - Your Model Railway Club
AuthorPost
 Posted: Sat Nov 2nd, 2019 10:54 pm
PMQuoteReply
link to this 1st post
Chubber
Casseroled Badger


Joined: Thu Oct 2nd, 2008
Location: Ivybridge, Devon, Gateway To Dartmoor.. , United Kingdom
Posts: 4593
Status: 
Offline

My photos:
view photos in Gallery
view photos as slides

Despite my previous misgivings about using Peco products after my experience with 'Technical Help' and their seemingly blasé view over customer choice and consultation, I have nonetheless bought lengths of Bullhead flexitrack as I can't go through the mind-numbing excercise of respacing the sleepers on finescale.It does look good, but is quite delicate, and easy to spoil with heavier handling. My 15% Expressways Models discount as an active S.D.R. volunteer takes bit of the sting out of it!

My dilemma is that only large radius L & R turnouts are currently being produced, and the the response 'Don't know when we will get round to producing more....we're very busy....' isn't exactly helpful. As I have a small stock of Code 75 turnouts, some still unused, I am prepared to use them and 'Technical help' told me to 'force' the end of the bullhead into the Code 75 joiners, as there are currently no plans to make an adaptive joiner either. [See 'Don't know etc above...']

Diabolical! That's the only polite way I have of describing the effort and ghastly effect. They look pretty piss-poor on code 75, on bullhead finescale they are laughable, so I have started to cut Code 75 joiners in half and remove the 'ramp' at the ends using my Dremel, and soldering the bullhead and the Code 75 turnout rail together to create a secure joint. Handling a normal sized joiner is bad enough, when less than 5mm long it becomes more problematic, espcially it you are trying to 'force' one end onto bullhead, and the other onto Code 75, so I have come up with a Mark 2 Chubber Putter-onner made from a length of brass tube and a scrap of bullhead rail. There's a drawing pin head soldered to the other end to protect the palm of your hand.

In use I open up one end of the shortened joiner with the Mk 2 and use the Mk 1 to push it onto the track before joining them. A touch of Fluxite and a quick in-and-out with a 25 watt iron does the trick.

'Ah!' I hear you say, 'what about the isolating joiner at frog ends...', well it is my intention to use a very fine cutting disc on the turnout track, the resulting gap to be filled with epoxy or similar.



From L - R,
Code 75 rail,
bullhead rail,
cut down joiner,
Peco bullhead joiner for b'head to b'head,
below an ordinary joiner,
top right the Mk 2 tool
and below the Mk 1 tool for code 75.

I hope that might help somebody else,

Poop-poop,

Douglas



____________________
'You may share the labours of the great, but you will not share the spoil...' Aesop's Fables

"Beer is proof that God loves us and wants us to be happy" - Benjamin Franklin

Back To Top PMQuoteReply

 Posted: Sun Nov 3rd, 2019 11:06 am
PMQuoteReply
link to this 2nd post
Chubber
Casseroled Badger


Joined: Thu Oct 2nd, 2008
Location: Ivybridge, Devon, Gateway To Dartmoor.. , United Kingdom
Posts: 4593
Status: 
Offline

My photos:
view photos in Gallery
view photos as slides

Doh! Forgot to uplaod a picture of the result, much neater, don't you think? You don't have to hack off the plastic chairs either.




Douglas



____________________
'You may share the labours of the great, but you will not share the spoil...' Aesop's Fables

"Beer is proof that God loves us and wants us to be happy" - Benjamin Franklin

Back To Top PMQuoteReply

 Posted: Sun Nov 3rd, 2019 12:00 pm
PMQuoteReply
link to this 3rd post
Ed
Full Member


Joined: Tue Jan 29th, 2013
Location: West Anglia Main Line, United Kingdom
Posts: 3743
Status: 
Offline

My photos:
view photos in Gallery
view photos as slides

Well done that man :thumbs :thumbs :thumbs


Ed



____________________
Engineers just love to change things
Back To Top PMQuoteReply

 Posted: Sun Nov 3rd, 2019 12:53 pm
PMQuoteReply
link to this 4th post
Headmaster
Full Member


Joined: Sun Jun 2nd, 2013
Location: Faversham, United Kingdom
Posts: 814
Status: 
Offline

My photos:
view photos in Gallery
view photos as slides

Very smart indeed!
Michael



____________________
Michael

Faversham Creek

"There is no harm in repeating a good thing." Plato
Back To Top PMQuoteReply

 Posted: Sun Nov 3rd, 2019 01:21 pm
PMQuoteReply
link to this 5th post
gastwo
Member


Joined: Sat Jul 30th, 2011
Location: Llechryd, Ceredigion, United Kingdom
Posts: 594
Status: 
Offline

My photos:
view photos in Gallery
view photos as slides

Headmaster wrote: Very smart indeed!
Michael

We have come to expect nothing less! :pathead

Back To Top PMQuoteReply

 Posted: Sun Nov 3rd, 2019 08:34 pm
PMQuoteReply
link to this 6th post
BCDR
Moderator


Joined: Sat Oct 19th, 2013
Location: Reston, Virginia USA
Posts: 3147
Status: 
Offline

My photos:
view photos in Gallery
view photos as slides

The code 83 joiners from Shinohara or Micro Engineering look about the same size as the "half" joiners. 

I thought you were going SMP points? I have not understood why Peco did introduce other turnouts either. Next year at the earliest.

Nigel



____________________
©Nigel C. Phillips
Back To Top PMQuoteReply

 Posted: Mon Nov 4th, 2019 11:52 am
PMQuoteReply
link to this 7th post
Chubber
Casseroled Badger


Joined: Thu Oct 2nd, 2008
Location: Ivybridge, Devon, Gateway To Dartmoor.. , United Kingdom
Posts: 4593
Status: 
Offline

My photos:
view photos in Gallery
view photos as slides

BCDR wrote: The code 83 joiners from Shinohara or Micro Engineering look about the same size as the "half" joiners. 

I thought you were going SMP points? I have not understood why Peco did introduce other turnouts either. Next year at the earliest.

Nigel


Well, Nigel, having revisited Ben Alder's brilliant 'Far North' where he is using C&L track with Peco turnouts, I decided that already having 5 of the 7 turnouts I need [two unused] and the associated packing I decided that Peco b'head flexitracks spacing would give me the same effect. Having formerly lived a few years in France, I did tend to over-buy during my U.K. visits.
If the result is half as good as 'Far North' then I'll be a happy chappy!

Poop-poop,

Douglas



____________________
'You may share the labours of the great, but you will not share the spoil...' Aesop's Fables

"Beer is proof that God loves us and wants us to be happy" - Benjamin Franklin

Back To Top PMQuoteReply

This is topic ID = 16260     Current time is 05:39 pm  
You are here:  Your Model Railway Club > Getting You Started. > Hints, Tips & Smaller Projects. > Peco Bullhead Track
You can type a quick reply to this topic here. Click in the box below to begin.

Or to reply to an individual post, or to include images, attachments and formatted text,
click the Quote or Reply buttons on each post above.

To start a new topic in this forum, click the Start New Topic button below.
To start a new topic in a different forum, click the Forum Jump drop-down list below.
Start New Topic


Back to top of page

           
15 Most Recent Topics

Problems with this web site? Please contact the Webmaster.

All material submitted to this web site is the responsibility of the respective contributor. By submitting material to this web site you acknowledge that you accept full responsibility for the material submitted.
Unless stated otherwise, all the material displayed on this web site, including all text, photographs, drawings and other images, is copyright and the property of the respective contributor. Registered members are welcome to use it for their own personal non-commercial modelmaking purposes. It must not be reproduced or re-published elsewhere in any form, or used commercially, without first obtaining the owner's express permission.
The owner of this web site may edit, modify or remove any content at any time without giving notice or reason.    © 2008

                 

Recent Topics Back to top of page

Powered by UltraBB 1.15 Copyright © 2007-2011 by Jim Hale and Data 1 Systems. Page design copyright © 2008-2013 Martin Wynne. Photo gallery copyright © 2009 David Williams.