Video Archive | Recent Topics |
---|
![]() |
||||||
| ||||||
Moderated by: Spurno |
|
Free Material - Baseboards. - Getting You Started. - Your Model Railway Club | ||||||||||
Author | Post | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||
wahiba Full Member ![]()
My photos:
![]() |
Visited IKEA at Warrington today. Outside they had three 'bins' with all sorts of wood based material with a note to 'help yourself'. Well I did to a few sheets of the hardboard that is stiffer and more like a thin fibre board often used as backing on some furniture. I do not know if every IKEA is doing this, but if you live near enough to one for regular visits it could be worth while. David ____________________ freelance model railways and tramways http://www.picsntech.co.uk |
|||||||||
|
| ||||||||||
Colin W Full Member ![]()
My photos:
![]() |
Sounds like that's MDF. If so, look up safe handling before any cutting, sawing or drilling. The very fine fibres are hazardous as they easily get / stay airborne. I try to avoid working any I have but it can make a useful base for individual building settings on your layout. swells up like a sponge if wetted so seal with a suitable primer, also helps prevent later damage. My favorite warning story about MDF is I found some being used as door architrave in a Venetian Pallazzo (P.Grimaldi) in the basement. Venice's basements being below water and permanently humid, these timbers had swollen up like Elephantitis to 3 or 4 times original size. ____________________ Colin Westown - Heathfield, Steam on the GWR |
|||||||||
|
| ||||||||||
wahiba Full Member ![]()
My photos:
![]() |
Not knowing the difference between hardboard and MDF I thought I would look it up. Seems that they are all variations of the same thing, but hardboard is harder than MDF which is the thin stuff I got from Ikea but seems to be harder and stiffer than hardboard from B&Q. I must say I assumed that is was just MDF. Quite an interesting bit about the stuff on Wikipedia. I suspect dust problems really require an industrial setting. Practically the biggeest problem is that it wears out non carbide cutting blades. ____________________ freelance model railways and tramways http://www.picsntech.co.uk |
|||||||||
|
| ||||||||||
BCDR Moderator ![]()
My photos:
![]() |
Usually known as Masonite . Small wood fibers mixed with paraffin wax and heated/pressed. Wear mask and goggles, even for home use. Level 1 carcinogen for humans. My local store will not cut this material. Neither will I, being allergic to the dust. The MSDS is interesting reading. They're giving it away because of the disposal cost. Take it back and tell them you are informing IKEA head office in Sweden. It needs to be recycled properly. Nigel ____________________ ©Nigel C. Phillips |
|||||||||
|
| ||||||||||
Petermac Moderator ![]()
My photos:
![]() |
"Masonite" in the States is what Euroeans call hardboard - named thus because it was invented by a guy called Mason. MDF - "medium density fibreboard" - is not the same stuff although both are made by bonding wood fibres together under pressure. In days of yore, it was suggested the glues used in the manufacture of MDF were carcinogenic. Whilst that is certainly not the case nowadays, the fine dust particles created by machining either material won't do you any good - but then that is the case with many materials so neiter MDF nor hardboard should be singled out as any more or less dangerous than many other products. In UK, unless wood yards have proper dust extraction equipment, H&S regulations prohibit their cutting it. I'd certainly go for it if I had an Ikea within striking distance of me. ![]() ____________________ 'Petermac |
|||||||||
|
| ||||||||||
BCDR Moderator ![]()
My photos:
![]() |
Wood dust is classified as a group 1 carcinogen. It is also a pulmonary irritant, and can cause allergic reactions. Same classification as tobacco smoking or strontium 90. Least exposure the better. Nigel ____________________ ©Nigel C. Phillips |
|||||||||
|
| ||||||||||
Colin W Full Member ![]()
My photos:
![]() |
There is a (practical) world of difference between MDF and Masonite/Hardboard. Because of the health hazard it is worth understanding. My dad built 2 sheds covered with Tempered Hardboard and they were still standing 50 years later. MDF is a much more recent incarnation of a similar concept. The difference according to Wikipedia is in how the fibres are produced. Masonite retains the timber's original lignin which then acts as its adhesive on forming, MDF is processed to break down the timber's lignins, then treated with a UF resin. The result of the UF treatment is very fluffy light fibres which are then compressed and bound together. Even normal old style hardboard does not swell up like typical MDF on the slightest exposure to water. Put one drop on a sample of both and you'll see the difference. MDF lends itself to being formed into thicker sheets and intricate shapes like architraves whereas hardboard AFAIK only ever came in the 1/8" and 1/4" pressed sheet with those indentations on the back, presumably from the press. MDF does go to dust easily whenever operated on. In increasing risk order , drilling, sawing, sanding. Untempered Hardboard with its indentations makes an excellent track cleaner. An idea I got from somewhere. Must do a post on it ____________________ Colin Westown - Heathfield, Steam on the GWR |
|||||||||
|
| ||||||||||
BCDR Moderator ![]()
My photos:
![]() |
Wood dust is wood dust. Doesn't matter where from. Chronic exposure leads to chronic inflammation, which leads to key cellular regulator mutations....work safely. Wood, lignins, note to self, remember thy botany ![]() Nigel ____________________ ©Nigel C. Phillips |
|||||||||
|
This is topic ID = 16245 Current time is 01:25 pm |
You are here: Your Model Railway Club > Getting You Started. > Baseboards. > Free Material | |||
You can type a quick reply to this topic here. Click in the box below to begin. Or to reply to an individual post, or to include images, attachments and formatted text, click the Quote or Reply buttons on each post above. To start a new topic in this forum, click the Start New Topic button below. To start a new topic in a different forum, click the Forum Jump drop-down list below. |
|
||
|
Back to top of page | ||
| |||
Problems with this web site? Please contact the Webmaster. |
All material submitted to this web site is the responsibility of the respective contributor. By submitting material to this web site you acknowledge that you accept full responsibility for the material submitted. |
Unless stated otherwise, all the material displayed on this web site, including all text, photographs, drawings and other images, is copyright and the property of the respective contributor. Registered members are welcome to use it for their own personal non-commercial modelmaking purposes. It must not be reproduced or re-published elsewhere in any form, or used commercially, without first obtaining the owner's express permission. |
The owner of this web site may edit, modify or remove any content at any time without giving notice or reason. © 2008 |
Recent Topics | Back to top of page | |
Powered by Copyright © 2007-2011 by Jim Hale and Data 1 Systems. Page design copyright © 2008-2013 Martin Wynne. Photo gallery copyright © 2009 David Williams. |