| You are here: Your Model Railway Club > Getting You Started. > The Lineside. > Buildings > Original Superquick Water tower & Weigh House Series A No.8 | To bottom of page |
| Video Archive | Recent Topics |
|---|
|
|
||||||
| ||||||
| Moderated by: Spurno |
|
|||||||||
| Original Superquick Water tower & Weigh House Series A No.8 - Buildings - Getting You Started. - Your Model Railway Club | ||||||||||
| Author | Post | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||
|
Gordon Curtis Full Member 
My photos:
|
Hi Folks, Another original 60s-style Superquick kit. Unlike the Supermarket, this kit was replaced with a similar one which is still in todays range. The build, however, is different, and the detail is a little different too. This old kit is still quite common and is easily identifiable by the weigh house which comes with it.  The new 40-year-old Superquick Water Tower & Weigh House kit Series A No. 8  The components of the Superquick kit  The walls made up and windows fixed into place. The walls are built up of two main layers which provide a reasonable joint. Plinths are fixed top and bottom to the side walls only. Tape is used to fix the windows in place (Holding the wall over the glass to get the position), then blobs of PVA provide a good hold.  The four triangular supports were glued to the end walls and left to dry – taking care to fix them right to the edge of the inner card.  The walls assembled together. I use a little PVA on the inside of the joint to keep it clean on the outside. When the joint has set, I blob PVA down the inside to help make it stronger.  While the Water Tower is setting, work can take place on the Weigh House. Here the walls have been made up and the window fixed into place.  The Weigh House walls. Card plinths are fixed to the side walls, paper plinths are cut to size and fixed to the end walls once assembled.  A detail of the Water Tower doorway. I was not happy with the two-thick card edges on the plinths, so opted to cut, chamfer and insert small sections of plinth. It might have been better to cut a groove from the back of the plinth and fold these.  The top section of the Water Tower is made up in a similar fashion to the bottom and again fixed on with a little PVA and bigger blobs on the inside. The roof was fixed to the Weigh House by using blobs of glue on the inside of the walls and the whole building held up-side-down. The chimney is made up from paper which you need to cut out and crease yourself. I find a chopstick handy to help glue it together! I had to cut the plinth away with a sharp knife to mount the chimney to the wall. The long piece in the photo is the ridge tiles which are cut, folded and glued before the tiles are shaped.  The completed Water Tower and Weigh House with Nellie No. 27. Because the brickwork is so dark on these, painting with watercolour along the edges of the card really improves the look. Windows and doorways were also painted brick by brick.  The backs of the buildings. Though it is not so easy to tell on these photographs, I found that painting every other brick first, and then filling in the gaps was the way to go. It took almost as long to paint the edges as it did to build them!  A slightly closer view!  A comparison of the 1960s Superquick kit and the very similar Metcalfe model released in a recent magazine. A daylight photograph to show the colour off better. The Superquick kit is made up from paper laminated onto brown card, and the Metcalfe kit is printed directly onto thin white card which is then re-enforced by brown card. I did not make up the Metcalfe kit quite as intended as I did not like the extra layer of brown card around the windows. The model would also be improved by painting in the white edges as I did with the Superquick models. Other than the materials, the models are printed in quite different colours – the Metcalfe being quite bright with exaggerated roof tiles, the Superquick model is printed in quite earthy tones by comparison. Thank you very much for reading about my latest build! Gordon |
|||||||||
| ||||||||||
| ||||||||||
|
MaxSouthOz Admin 
My photos:
|
Very nice, Gordon.  ____________________ Max Port Elderley |
|||||||||
| ||||||||||
| ||||||||||
|
Sol A modelling Moderator. 
My photos:
|
While the Scalescenes Water tank is cheaper by 2 pound, the time taken is far longer with Scalescenes & the final result does not appear to be much different than the Superquick build. A nice job Gordon ____________________ Ron NCE DCC ; 00 scale UK outline. |
|||||||||
| ||||||||||
| ||||||||||
|
Gordon Curtis Full Member
My photos:
|
Thanks for the nice comments. Superquick the kit might be called, but there are still a few evenings work to get it to that stage – Well, for me there are anyway! I like the look of the Scalescenes water tower model (I've just had a quick peek on their website). I wouldn't trust the ink in my printer to be light-fast enough. I printed out some pictures for my boy's wall a year or so ago, and they're looking very faded now, but then that was using budget ink cartridges... Gordon |
|||||||||
| ||||||||||
| ||||||||||
|
Marty Enjoying the Journey 
My photos:
|
A good demonstration of the potential of these kits. Well done Gordon. ____________________ Marty N Gauge, GWR West Wales Newcastle Emlyn Layout. Newcastle Emlyn Station is "Under construction" |
|||||||||
| ||||||||||
| ||||||||||
|
Gordon Curtis Full Member
My photos:
|
Thanks Marty, As these original kits are now several decades old and many people, including myself, will not remember or will not have built them, I thought it would be interesting to post the builds on here. They still come up on eBay, some more so than others, so folks can decide whether to try an original kit, or one of the newer ones, or do both! I've been surprised at how fresh the kits look, despite being as old as I am! I should have another dropping through the door soon, and am looking forward very much to building it. I'll try to get it posted too when done. Gordon :-) |
|||||||||
| ||||||||||
| ||||||||||
|
sparky Member
My photos:
|
Nice build Gordon. I found i had to spray scalescenes printed sheets with a fixative to help keep from fading.. also helps should the glue(in my case pritstick) wonder on to the printed side in error. ____________________ reg |
|||||||||
| ||||||||||
| ||||||||||
|
Gordon Curtis Full Member
My photos:
|
Thanks Sparky, and a good idea using the fixative. On the subject of getting glue where it shouldn't go – I managed to dip my sleeve in the glue while I was building one of the models. What should one do – abandon the model or let the shirt get ruined? Well, it was an old shirt... Gordon :-) |
|||||||||
| ||||||||||
| This is topic ID = 15393 Current time is 11:08 pm |
| You are here: Your Model Railway Club > Getting You Started. > The Lineside. > Buildings > Original Superquick Water tower & Weigh House Series A No.8 | |||
|
You can type a quick reply to this topic here. Click in the box below to begin. Or to reply to an individual post, or to include images, attachments and formatted text, click the Quote or Reply buttons on each post above. To start a new topic in this forum, click the Start New Topic button below. To start a new topic in a different forum, click the Forum Jump drop-down list below. |
|
||
|
Back to top of page | ||
| |||
| Problems with this web site? Please contact the Webmaster. | |||
| All material submitted to this web site is the responsibility of the respective contributor. By submitting material to this web site you acknowledge that you accept full responsibility for the material submitted. |
| Unless stated otherwise, all the material displayed on this web site, including all text, photographs, drawings and other images, is copyright and the property of the respective contributor. Registered members are welcome to use it for their own personal non-commercial modelmaking purposes. It must not be reproduced or re-published elsewhere in any form, or used commercially, without first obtaining the owner's express permission. |
| The owner of this web site may edit, modify or remove any content at any time without giving notice or reason. © 2008 |
| Recent Topics | Back to top of page | |
|
Powered by Copyright © 2007-2011 by Jim Hale and Data 1 Systems. Page design copyright © 2008-2013 Martin Wynne. Photo gallery copyright © 2009 David Williams. |
||