Video Archive | Recent Topics |
---|
![]() |
||||||
| ||||||
Moderated by: Spurno |
|
Cobalt help wanted - DCC - Tutorials - Getting You Started. - Your Model Railway Club | ||||||||||
Author | Post | |||||||||
---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||
g0ibi Full Member ![]()
My photos:
![]() |
I have ordered a Cobalt AD-8fx control board for my layout. I intend to use Peco surface mounted and Seep PM2 point motors with control from the Digitrax controller. Looking at the service/instruction sheet only shows Cobalt motors being used! Could someone show me the wiring for this set up please? AD-8fx to Seep/Peco motors please?? Thanks Ron ____________________ Proper Preparation makes for Perfect Performance!! http://yourmodelrailway.net/view_topic.php?id=13331&forum_id=21 |
|||||||||
|
| ||||||||||
toto Former Member
My photos:
![]() |
Hi Ron, Are the seep motors not analogue motors ? If so I'm not so sure they'll go with the Cobalt switch. Hope I'm wrong. toto |
|||||||||
|
| ||||||||||
g0ibi Full Member ![]()
My photos:
![]() |
It says so on the advertisements Tom!! ____________________ Proper Preparation makes for Perfect Performance!! http://yourmodelrailway.net/view_topic.php?id=13331&forum_id=21 |
|||||||||
|
| ||||||||||
toto Former Member
My photos:
![]() |
That's good then, you're on a winner. Just a case of working out how they wire up together. How many sets of points will you be using ? |
|||||||||
|
| ||||||||||
g0ibi Full Member ![]()
My photos:
![]() |
2 sets of cross-overs and 6 others in the yard (hopefully!) The Digitrax controller is set up to use over 100 points! Cheers Ron ____________________ Proper Preparation makes for Perfect Performance!! http://yourmodelrailway.net/view_topic.php?id=13331&forum_id=21 |
|||||||||
|
| ||||||||||
toto Former Member
My photos:
![]() |
Hi Ron, Plenty capacity with the Digitrains then. If you could copy up the instructions off the cobalt unit and the swept could be helpful. Toto |
|||||||||
|
| ||||||||||
g0ibi Full Member ![]()
My photos:
![]() |
'Swept would be helpful'?? ____________________ Proper Preparation makes for Perfect Performance!! http://yourmodelrailway.net/view_topic.php?id=13331&forum_id=21 |
|||||||||
|
| ||||||||||
toto Former Member
My photos:
![]() |
Sorry Ron, The seep motors. |
|||||||||
|
| ||||||||||
RFS Full Member
My photos:
![]() |
There are two versions - one for Cobalts (DCD-AD8FX) and one for Solenoids (DCD-ADS8FX). http://www.ehattons.com/80701/DCC_Concepts_DCD_ADS8FX_COBALT_Solenoid_Accessory_Decoder_8_Output_/StockDetail.aspx http://www.ehattons.com/80699/DCC_Concepts_DCD_AD8FX_COBALT_ip_Accessory_Decoder_8_Way_/StockDetail.aspx Sounds like you may have the wrong one? ____________________ Robert |
|||||||||
|
| ||||||||||
g0ibi Full Member ![]()
My photos:
![]() |
Thanks Robert will check it out and change the order if I can!! Cheers Ron ____________________ Proper Preparation makes for Perfect Performance!! http://yourmodelrailway.net/view_topic.php?id=13331&forum_id=21 |
|||||||||
|
| ||||||||||
16A Deceased Member ![]()
My photos:
![]() |
Hi Ron The 'S' in the product number indicates 'solenoid' and the 8 is a bank of 4 x ads-2's on one pcb (4x2=8). I can't find a wiring diagram in my archive for the ads-8 but this one for the ads-2 should suffice. The good thing about dcc concepts decoders is that they (the decoders) have terminals marked with what they are for so it shouldn't prove at all difficult... They will work on DC at 12 - 14v or DCC on the bus at 16vAC. http://www.gaugemaster.com/instructions/dcc_concepts/ads%20instruction.pdf ____________________ Mike Praise is an excellent fillip for waning ambition. |
|||||||||
|
| ||||||||||
g0ibi Full Member ![]()
My photos:
![]() |
Cheers Mike, re-ordered today, (I must start reading adverts properly!!) Going to use the Digitrax controller to activate the points and maybe build a diagram board for LED's? Cheers Ron Attachment: MR-N202-11-ADS-2fx-Solenoid-Decoders-2014.pdf (Downloaded 2 times) ____________________ Proper Preparation makes for Perfect Performance!! http://yourmodelrailway.net/view_topic.php?id=13331&forum_id=21 |
|||||||||
|
| ||||||||||
RFS Full Member
My photos:
![]() |
Bear in mind with these DCC Concepts controllers that they do not remember the position of the points following a power outage - ie intermittent short, or start of the session. This means that any LEDs will not necessarily indicate the correct position until you activate the points again. This can be a bit more of a pain if you're not using the switch for LEDs but for frog polarity switching.
____________________ Robert |
|||||||||
|
| ||||||||||
g0ibi Full Member ![]()
My photos:
![]() |
Understood Robert, there's always a down side!! Cheers Ron ____________________ Proper Preparation makes for Perfect Performance!! http://yourmodelrailway.net/view_topic.php?id=13331&forum_id=21 |
|||||||||
|
This is topic ID = 13397 Current time is 10:48 pm |
You are here: Your Model Railway Club > Getting You Started. > Electrics - DCC > DCC - Tutorials > Cobalt help wanted | |||
You can type a quick reply to this topic here. Click in the box below to begin. Or to reply to an individual post, or to include images, attachments and formatted text, click the Quote or Reply buttons on each post above. To start a new topic in this forum, click the Start New Topic button below. To start a new topic in a different forum, click the Forum Jump drop-down list below. |
|
||
|
Back to top of page | ||
| |||
Problems with this web site? Please contact the Webmaster. |
All material submitted to this web site is the responsibility of the respective contributor. By submitting material to this web site you acknowledge that you accept full responsibility for the material submitted. |
Unless stated otherwise, all the material displayed on this web site, including all text, photographs, drawings and other images, is copyright and the property of the respective contributor. Registered members are welcome to use it for their own personal non-commercial modelmaking purposes. It must not be reproduced or re-published elsewhere in any form, or used commercially, without first obtaining the owner's express permission. |
The owner of this web site may edit, modify or remove any content at any time without giving notice or reason. © 2008 |
Recent Topics | Back to top of page | |
Powered by Copyright © 2007-2011 by Jim Hale and Data 1 Systems. Page design copyright © 2008-2013 Martin Wynne. Photo gallery copyright © 2009 David Williams. |